www.rfm.com e-mail: info@rfm.com page 1 of 3 ?2008-2010 by rf monolithics, inc. OP4013B - 2/8/10 electrical characteristics characteristic sym notes minimum typical maximum units operating frequency absolute frequency f o 1, 9 693.483 mhz tuning frequency range 2 100 ppm tuning voltage range 1 0 +3 v tuning linearity 1, 8 5% modulation bandwidth 125 265 khz q and q output voltage into 50 ? (vswr<1.2) v o 1,3 0.60 1.1 v p-p operating load vswr 1,3 2:1 symmetry 3, 4, 5 49 51 % harmonic spurious 3, 4, 6 -30 dbc nonharmonic spurious 3, 4, 6, 7 -60 dbc phase noise @100 hz offset -70 dbc/hz @1 khz offset -100 dbc/hz @10 khz offset -125 dbc/hz noise floor -150 dbc/hz q and q jitter rms jitter 3, 4, 6, 7 2 ps p-p no noise on v cc 3, 4, 6, 7 12 ps p-p 200 mv p-p from 1 mhz to ? f o on 312 ps p-p output dc resistance (between q & q )1, 350 k ? dc power supply operating voltage v cc 1, 3 3.13 3.3, 5.0 5.25 vdc operating current i cc 1, 3 70 ma operating case temperature t c 1, 3 -10 +80 c lid symbolization (yy=year, ww=week) rfm OP4013B yyww smc-08 ? quartz saw stabilized and filtered ?diff sine? technology fundamental-mode oscillation at 693.48342 mhz voltage tunable for phase lock loop operations optical timing reference for 10g eithernet applications complies with directive 2002/95/ec (rohs) the output of this device is generated and filtered by narrowband quartz saw elements at 693.48 mhz. the configuration of this clock is intended to provide a pure signal for optical timing applications in noisy signal environments. the q/qbar differential output swing of 1 volt about 0 vdc has symmetry better than 1% into loads from 40 to 70 ohms; determined by customer application. the long term frequency accuracy is set by an external reference source allowing this device to complete a phase lock loop design without the usual noise and jitter problems associated with pll?s. absolute maximum ratings rating value units dc suppy voltage 0 to 5.5 vdc tuning voltage 0 to 5.5 vdc case temperature -55 to 100 c 693.48342 mhz optical timing clock OP4013B caution: electrostatic sensitive device. observe precautions for handling. cocom caution: approval by the u.s. department of commerce is required prior to export of this device. notes: 1. unless otherwise noted, all specifications include any combination of load vswr, vcc, and tc. in addition, q and q are terminated into 50 ? loads to ground. (see: typical test circuit.) 2. customer useful tune range in excess of what part requires over temp, aging, pushing, pulling & accuracy. 3. the design, manufacturing process, and specifications of this device are subject to change without notice. 4. only under the nominal conditions of 50 ? load impedance with vswr 1.2 and nominal power supply voltage. 5. symmetry is defined as the pulse width (in percent of total period) measured at the 50% points of q or q . (see: timing definitions.) 6. jitter and other spurious outputs induced by externally generated electrical noise on v cc or mechanical vibration are not included in this specification, except where noted. external voltage regulation and careful pcb layout are recommended for optimum performance. 7. applies to period jitter of q and q . measurements are made with the tektronix csa803 signal analyzer with at least 1000 samples. 8. linearity is a function of the percentage variation from a permitted linear deviation versus the amount of frequency tune ran ge. see linearity definition. 9. one or more of the following united states patents apply: 4,616,197; 4,670,681; 4,760,352.
www.rfm.com e-mail: info@rfm.com page 2 of 3 ?2008-2010 by rf monolithics, inc. OP4013B - 2/8/10 smc-8 8-terminal surface mount case dimension mm inches min max min max a 13.46 13.97 0.530 0.550 b 9.14 9.66 0.360 0.380 c 1.93 nominal 0.076 nominal d 3.56 nominal 0.141 nominal e 2.24 nominal 0.088 nominal f 1.27 nominal 0.050 nominal g 2.54 nominal 0.100 nominal h 3.05 nominal 0.120 nominal j 1.93 nominal 0.076 nominal k 5.54 nominal 0.218 nominal l 4.32 nominal 0.170 nominal m 4.83 nominal 0.190 nominal n 0.50 nominal 0.020 nominal a b n j l (x2) d (x8) k (x8) c h g m (x3) e f electrical connections terminal number connection 1 v cc 2 ground 3 enable/disable 4 q output 5q output 6 ground 7 8 tune input lid ground block diagram q v cc buffer amplifier saw oscillator _ v tune q 1 2 3 4 8 7 6 5 top view op performance curves and application information see the op4005b data sheet for typical op performance curves and application information.
www.rfm.com e-mail: info@rfm.com page 3 of 3 ?2008-2010 by rf monolithics, inc. OP4013B - 2/8/10 smc-08 case reel size quantity per reel ?b? nominal ?c? nominal min max 13 inch 330 mm 100 mm 200 1000 dimensions carrier tape dimensions cover tape size ao .383 .004 (9.7 mm) 21.3 mm bo .554 .004 (14.1 mm) ko .130 .004 (3.3 mm ) p 12 mm w 24 mm tape length 60 m pockets/m 83 see detail "a" 1 3 . 0 2 0 . 2 2.0 24.4 " c " r e f . " b " r e f . (measurements in millimeters) detail "a" orientation in tape carrier as shipped w (carrier tape size) a o b o p (pitch) cover tape size k o cover tape
|
